Resin

puffpuffpass · Post by **puffpuffpass** » Mon Apr 28, 2003 1:00 pm

Yo... im new to usin bowls all the time and i was wonderin what I gotta do to scrape my resin... mine is like all sticky and nasty and is hard to scrape out.... my friend says i need to do a resin burn... wtf is that?

thanx

Post by **Weedguru Higher** » Mon Apr 28, 2003 1:15 pm

Can't help ya much with that one, cause I don't scrape my bowl I clean it with alcohol.

Weedguru Anex · Post by **Weedguru Anex** » Mon Apr 28, 2003 3:02 pm

I don't quite follow what your asking but I assume a resin burn is where you use your lighter over the edge of the res to make it crumbly before you load the bowl or what ever?

jonny cockeral · Post by **jonny cockeral** » Mon Apr 28, 2003 3:49 pm

i know what you mean. you could let the bowl dry out so its easier too scrape thats what i do. i have 2 bowls though

The Venal Marijuana God · Fri May 02, 2003 10:03 am

the resin is left on the bowl after smoking, if the resin is black its not worth smoking. but if its brown or dark brown its good. its really hard to srape the bowl of resin. what you need is a lighter and a bowl. a real bowl, you know for like coa coa pops. you get your bowland heat the resin inside for about 2 minutes at 10 seconds with 4-5 second intervals before starting to heat the resin again for another 10 seconds. after 2 mins the hash should be easier to scrape out. but you need to place the real bowl under neath your smoking bowl, because some resin falls out the bottom of the bowl when your scraping and lighting. hope this helps, and what your left over with is not pure hash, low quality. but its still smokable and should get you stoned if you have about 0.5g-1g of resin.
peace.

KingPing · Post by **KingPing** » Fri May 02, 2003 2:54 pm

I hvae allways used just rubbing alcohole and i collected all of the alchole and the resin and i letted it evaporate int he sun till just the resin was left and i smoked the resin.It works but i dont know how healthy it is for you.

jonny cockeral · Post by **jonny cockeral** » Fri May 02, 2003 4:11 pm

thats cool advice from venal... sum of this stuff should be on the main site

Post by **Weedguru Higher** » Fri May 02, 2003 8:59 pm

The Venal Marijuana God wrote:the resin is left on the bowl after smoking, if the resin is black its not worth smoking. but if its brown or dark brown its good. its really hard to srape the bowl of resin. what you need is a lighter and a bowl. a real bowl, you know for like coa coa pops. you get your bowland heat the resin inside for about 2 minutes at 10 seconds with 4-5 second intervals before starting to heat the resin again for another 10 seconds. after 2 mins the hash should be easier to scrape out. but you need to place the real bowl under neath your smoking bowl, because some resin falls out the bottom of the bowl when your scraping and lighting. hope this helps, and what your left over with is not pure hash, low quality. but its still smokable and should get you stoned if you have about 0.5g-1g of resin.
peace.

Except you're burning alot of the precious THC and it's not going into your lungs....

Daddy · Post by **Daddy** » Sat May 03, 2003 5:02 pm

Simply smoke proper weed fine skunk from the earth instead of that oil crap

Funk Doctor · Post by **Funk Doctor** » Sat May 03, 2003 5:46 pm

mena_toker_hey · Post by **mena_toker_hey** » Sat May 03, 2003 11:59 pm

just soak your gause or bowl in a nice glass of rumplemints or aftershock or vodka or whiskey and ;et it dissolve the resin. drink the drink and it will work.

SORTED

jonny cockeral · Post by **jonny cockeral** » Sun May 04, 2003 2:18 pm

bit exspensive aint it!

Post by **Weedguru Higher** » Sun May 04, 2003 6:36 pm

Well, you could always rob your mother's liquor cabinet.........

www.weedguru.com

Resin

Resin

Who is online