how to clean your pipe?
Moderator: Moderators
-
Ikku
- Sir Toke-a-lot

- Posts: 2687
- Joined: Fri Feb 04, 2005 2:12 am
- Contact:
-
swanee89
- The Duke of Dope

- Posts: 1722
- Joined: Wed Apr 04, 2007 8:21 pm
- Location: Illinois
- Contact:
^that kind of stuff is always like overpriced windex or some shit. if you got a bottle handy read the label and let us in on the active ingerdients
[img]http://i187.photobucket.com/albums/x106/swanee89/rs_sig2.jpg[/img]
"Bob Dylan impresses me about as much as... well, I was gonna say a slug but I like slugs."
-Captain Beefheart
"Bob Dylan impresses me about as much as... well, I was gonna say a slug but I like slugs."
-Captain Beefheart
-
Ikku
- Sir Toke-a-lot

- Posts: 2687
- Joined: Fri Feb 04, 2005 2:12 am
- Contact:
-
king
- Bonghead

- Posts: 354
- Joined: Mon Jul 09, 2007 10:58 pm
- Contact:
if you use water to clean out ya pipe is there a chance of mold forming in the inside when ya let it dry out? cause i just cleaned mines out with hot water and used a toothpick to scrape the inside and then also put some salt water in the inside covered all the holes and shook it around...now im just lettin it dry out....i also used a q-tip to scrape the inside once again at the end....my main concern is mold..

"penning these lyrics from a hammock, with a ounce of kush a pack of bamboos and an ice-cream sandwich" ~Curren$y
-
Gorecore
- Weedguru Grampy

- Posts: 4115
- Joined: Wed Dec 01, 2004 8:33 pm
- Location: Nova Scotia, Canada
- Contact:
Hey King. I wouldn't worry about mold forming in your pipe.
As for cleaning my glass pipe, I do it two different ways depending on how much time and effort I want to put into it.
One method I use is dropping it in a used butter container with a lid and pouring in enough rubbing alcohol to cover the pipe holes. I let it sit nearby and give the container a few light shakes every half hour. I've let the pipe sit in that bath overnight but leaving it in for an hour or two usually does the trick. Then I delicately hold it under the scalding hot running tap water and rinse the shit out of that bitch! That's when most of the resin, tar, and ash falls out into the sink. Let dry for a bit and then it's good to go.
The other method was already mentioned with heating the resin in the bowl and scraping it out. I usually follow up with using a twist tie cleaning in through the carb hole on the side. The paper/plastic edges of the twist tie really help gather the sludge from the walls of the bowl and stem.
I've heard that pure lemon juice (like the kind used for cooking) mixed with table salt works really well. Has anyone tried that method of cleaning?
As for cleaning my glass pipe, I do it two different ways depending on how much time and effort I want to put into it.
One method I use is dropping it in a used butter container with a lid and pouring in enough rubbing alcohol to cover the pipe holes. I let it sit nearby and give the container a few light shakes every half hour. I've let the pipe sit in that bath overnight but leaving it in for an hour or two usually does the trick. Then I delicately hold it under the scalding hot running tap water and rinse the shit out of that bitch! That's when most of the resin, tar, and ash falls out into the sink. Let dry for a bit and then it's good to go.
The other method was already mentioned with heating the resin in the bowl and scraping it out. I usually follow up with using a twist tie cleaning in through the carb hole on the side. The paper/plastic edges of the twist tie really help gather the sludge from the walls of the bowl and stem.
I've heard that pure lemon juice (like the kind used for cooking) mixed with table salt works really well. Has anyone tried that method of cleaning?

-
Pura Vida
- Bonghead

- Posts: 100
- Joined: Fri Aug 24, 2007 1:20 am
- Contact:
hmm I never thought of that...is it okay if you dry it right away?king wrote:if you use water to clean out ya pipe is there a chance of mold forming in the inside when ya let it dry out? cause i just cleaned mines out with hot water and used a toothpick to scrape the inside and then also put some salt water in the inside covered all the holes and shook it around...now im just lettin it dry out....i also used a q-tip to scrape the inside once again at the end....my main concern is mold..
[img]http://i37.photobucket.com/albums/e53/Doom_Goat/sigs/banner124.png[/img]
-
swanee89
- The Duke of Dope

- Posts: 1722
- Joined: Wed Apr 04, 2007 8:21 pm
- Location: Illinois
- Contact:
@ ikku: im not saying its windex but you know what i mean. they just repackage something you could get for a loot cheaper and charge you twice the price cause its a "specialty cleaner"
[img]http://i187.photobucket.com/albums/x106/swanee89/rs_sig2.jpg[/img]
"Bob Dylan impresses me about as much as... well, I was gonna say a slug but I like slugs."
-Captain Beefheart
"Bob Dylan impresses me about as much as... well, I was gonna say a slug but I like slugs."
-Captain Beefheart
-
Ikku
- Sir Toke-a-lot

- Posts: 2687
- Joined: Fri Feb 04, 2005 2:12 am
- Contact:
-
king
- Bonghead

- Posts: 354
- Joined: Mon Jul 09, 2007 10:58 pm
- Contact:
-
Weedguru Higher
- Tetrahydrocannabinologist

- Posts: 14620
- Joined: Sun Mar 30, 2003 1:31 pm
- Location: Canada
- Contact:
Who is online
Users browsing this forum: No registered users
