Car audio help

Technical / Computer related discussion board.

Moderator: Moderators

Post Reply
Vinyl
Herbal Assassin
Herbal Assassin
Posts: 910
Joined: Sat Nov 11, 2006 12:06 am
Contact:

Car audio help

Post by Vinyl »

here are two posts i made in a different forum, i havent been able to get much help there so im gonna try this here.

first post:

i have 2 infinity reference 1200W 12" subwoofers, hooked up to a 600W kenwood 2 channel amp(KAC-7285) i want to know if i can bridge the subs to get more power. the output is arranged like this : + - - +. it shows on the amp a line connecting the first + and the second - saying bridged. but i don't know where to hook up one sub like that and the other sub using the remaining terminals. or should i connect both the - leads to the second - and both the + leads to the first +. and i'm not even sure if this is possible. the amp was given to me so i don't know the lowest impedance it can go while staying stable. can anyone help me out? i'm kind of a noob at this.

any help is greatly appreciated, and will probably prevent fist marks from appearing in my walls.


and the second post, with pics:

I realized my first post was kind of hard to follow, so i took some pics of the amp to show you guys what i'm talking about. The first pic shows how i have it wired right now. I don't know if this is correct, or if i should remove the wires from one sub and put them in the empty terminals. which way of hooking them up will yeild the most power? and which way will result in NOT frying anything. the second and third pics are just of the amp and subs.

and now the pics:
Image
Image
Image
[img]http://img183.imageshack.us/img183/5183/sigab4.jpg[/img]
Toke now, or forever hold your piece
MrWizard
Bonghead
Bonghead
Posts: 129
Joined: Sat Jun 24, 2006 11:08 pm
Location: Wisconsin, USA
Contact:

Post by MrWizard »

(DISCLAIMER: I DO NOT CLAIM TO BE A CAR AUDIO EXPERT, NOR DO I NECESSARILY KNOW WHAT THE FUCK I AM TALKING ABOUT!)

Now that we have that little note out of the way, I would highly recommend this. I don't know how much of this you already know, but I found it did a good job of filling in the gaps in what I don't know. A lot of this depends on your speaker's impedance - as long as they are 4 ohms or higher impedance, you can bridge the output and wire the speakers in parallel (which is how you already have them). So, if nothing's blowing up right now, you pretty much have it set up as good as it's going to get without a new amp or speakers.
weedguru tom
← i ♥ weed →
←  i ♥ weed  →
Posts: 7448
Joined: Wed Apr 02, 2003 5:11 pm
Contact:

Post by weedguru tom »

get a 1200W amp
IcIrIs
Bonghead
Bonghead
Posts: 350
Joined: Wed Oct 04, 2006 2:51 am
Location: Canada, BC
Contact:

Post by IcIrIs »

I didnt read anyone else's posts they might have already said this but here is the right way to hook it up from what I have done with stereo equipment.

The best way to run speakers is in serise not perilel. That that means is it is hooked up like this
|----------- +Amp
+
Sub 1
-
|
|
+
Sub 2
-
|
|__________ - Amp

That way the sound is crisp and evenly distributed, and if you get a searge it will only blow one sub and not both.

Nice box by the way did you do it yourself?
Hey Hey Hey, Smoke Weed Everyday!
Vinyl
Herbal Assassin
Herbal Assassin
Posts: 910
Joined: Sat Nov 11, 2006 12:06 am
Contact:

Post by Vinyl »

well guys thanks for the help, i think that 2 channel amp i was given was a dud, so i switched back to the 4 channel that had the instruction manual and i knew how to use it. the system pumps!! im being deafened by it right now.

which box are you talking about? the sub box i did not make by myself, it is a bassworx. but the orange box that houses the 6 x9 s and he old subs (now just dummies) was all made by me. (took a really long time and weighs over 120 pounds :shock: )
[img]http://img183.imageshack.us/img183/5183/sigab4.jpg[/img]
Toke now, or forever hold your piece
buck333
Casual toker
Casual toker
Posts: 64
Joined: Wed Nov 15, 2006 3:09 am
Contact:

Post by buck333 »

IcIrIs wrote:I didnt read anyone else's posts they might have already said this but here is the right way to hook it up from what I have done with stereo equipment.

The best way to run speakers is in serise not perilel. That that means is it is hooked up like this
|----------- +Amp
+
Sub 1
-
|
|
+
Sub 2
-
|
|__________ - Amp

That way the sound is crisp and evenly distributed, and if you get a searge it will only blow one sub and not both.

Nice box by the way did you do it yourself?
from what I know this is the ideal setup, and I agree, thats a badass box and really nice looking system..have fun jammin lol
Vinyl
Herbal Assassin
Herbal Assassin
Posts: 910
Joined: Sat Nov 11, 2006 12:06 am
Contact:

Post by Vinyl »

thanks for all the help guys. i infact put the amp pictured above back in the system, hooked the subs up in series and whooollyyy crapp. it hauls like 100x more ass. its intense. i also added a CD player deck with a radio and its great. its got enough power that i over powered some idiot showing off on my street from inside my house. his car just couldn't compete 8)
[img]http://img183.imageshack.us/img183/5183/sigab4.jpg[/img]
Toke now, or forever hold your piece
Post Reply

Who is online

Users browsing this forum: No registered users