Page 1 of 2
how to clean your pipe?
Posted: Thu Aug 23, 2007 1:22 pm
by joey is a noob
j.w cause my small little pipe keeps piling on this black stuff in the bowl and i cant get it out...so far i've tried with a kleenex and water and a toothpick(lol)....so how do you keep your pipe nice and clean?
Posted: Thu Aug 23, 2007 1:38 pm
by onelove-maryjane
dont use kleeenex thats for sure. ever heard of a pipe cleaner? or u can pop it in the dishwasher. or u can just scrape the black stuff out with like a bent paperclip or safety pin. i wouldnt worry about it. its only resin, everybodys pipe has it
Posted: Thu Aug 23, 2007 2:00 pm
by SpRi7e
I forget exactly what I used to do but it was like, you get rubbing alcohol and water (or salt water, can't remember) and put them in a bag with your bowl and put a bigger bag over that one so nothing accidentally rips so your soaking wet. Then shake it for a good 10 minutes and after that dump everything out and rinse it with water then get a q-tip and scrub the inside out. If you do that then your bowl will be about 99% clean except for the spots you couldn't completely get.
Posted: Thu Aug 23, 2007 2:15 pm
by Sm0kyMcPot
hold ur bowl upside down and heat the res up with a lighter and take pretty much anything and scrape it out, nothing sharp though dont want to scratch the bowl but if u heat the res first it comes off clean as a whistle, SPri7es way is a good way to deep clean and mines just to clean it off after each session or whenever.
Posted: Thu Aug 23, 2007 3:35 pm
by logically
or you could fill up a pot with water, put your pipe in the pot and than boil the water. Of course only do that if you have a glass pipe. And be really careful too. And whatever you do, don't take the pipe out of hot water and than run it under cold water. I always boil my pieces to get them super clean.
Posted: Thu Aug 23, 2007 4:12 pm
by Sm0kyMcPot
u also have the risk of the piece melting to the pot as well
Posted: Thu Aug 23, 2007 5:29 pm
by t3h_shitz
Sm0kyMcPot wrote:u also have the risk of the piece melting to the pot as well
Not if it's glass. You're holding a flame to it, so some boiling water won't hurt anything.
Posted: Thu Aug 23, 2007 7:34 pm
by leprechaun
you be holding a flame to every sort of pipe, how else would u burn it
Posted: Thu Aug 23, 2007 8:02 pm
by swanee89
yea, resin is a lot easier to remove when its had a flame to it. comes out like butter after that
Posted: Thu Aug 23, 2007 8:44 pm
by Liles
Sm0kyMcPot wrote:u also have the risk of the piece melting to the pot as well
The melting point of iron is 1538 °C and steel somewhere along the 1300's.
If you can boil water to 1300°C then you're a mastermind...
EDIT: Reread, by melting to I assumed metal

Posted: Thu Aug 23, 2007 10:13 pm
by logically
logically wrote:or you could fill up a pot with water, put your pipe in the pot and than boil the water. Of course only do that if you have a glass pipe. And be really careful too. And whatever you do, don't take the pipe out of hot water and than run it under cold water. I always boil my pieces to get them super clean.
Posted: Fri Aug 24, 2007 2:49 am
by (weedguru)scarf
i use my fingers to plug all three holes of the pipe...
fill it with nail polish remover (acetone free)...shake
and rinse with boiling water... repeat again
and it cleans no problem
Posted: Fri Aug 24, 2007 4:18 am
by Anonymous Dude
Just today I used a pipe cleaner to clean out my pipe
Posted: Fri Aug 24, 2007 1:25 pm
by Pura Vida
I straight pour running water from my sink on it and it usually works...
Posted: Fri Aug 24, 2007 4:29 pm
by Sm0kyMcPot
one of my friends had his piece melt to the pot he was using...idk how he managed to do it but he ended up breaking it trying to get it off.