Page 1 of 1

how do u do that lighter trick?

Posted: Thu Sep 14, 2006 6:39 am
by blackmamba808
my friend has this lighter that he bought from 7-11 and it has a flame thats like 4 inches high.. i askd him how he did it but we were both stond and i don remember at alllll. i really wanna know now. please help

Posted: Thu Sep 14, 2006 1:50 pm
by Dr. Greenthumb
It need to be a lighter with a butane control knob. You need to lift up the knob and keep turning the release(righty tighty, lefty loosy). The looser it is the higher the flame will be.

Don't use it for smoking. It's all fun and games till someone burns their eyebrows.

Posted: Thu Sep 14, 2006 2:14 pm
by weedguru tom
yah we do that, with normal lighters, take of the metal clip, turn to full lift it off the cog move to the left put it back on the cog move to the right and repeat, you dont wanan do it too high or it just spits fire out in drips lol.

Posted: Thu Sep 14, 2006 2:51 pm
by weedguru+chrisisonfire
i do that with my zippo. Load it up nice and tight with fluid, turn it upside down right before the first drop of fluid comes out the wick, turn it back on the right side, then light. THe flame goes about 3 inches high. Then you just suck that flame in your j and you have a nice burn and the rest is history!

Posted: Thu Sep 14, 2006 10:24 pm
by Dakine
I always turn my zippo upside down when im filling anyways. and yes it does. xD Rigged plastic lighters with the metal bit put back are a great practical joke.

Posted: Thu Sep 14, 2006 11:00 pm
by SomeONE?
Dakine wrote:I always turn my zippo upside down when im filling anyways. and yes it does. xD Rigged plastic lighters with the metal bit put back are a great practical joke.
lol until some one goes to light there joint with it and cathces their hair on fire :lol:

Posted: Thu Sep 14, 2006 11:27 pm
by Dakine
haha, yeah

Posted: Fri Sep 15, 2006 6:50 am
by blackmamba808
how do u get that dam metal clip thing off? and once its off...wat do u do again? thanks for the help here. really wanna get my frien back

Posted: Fri Sep 15, 2006 8:54 am
by Weedguru_RyaNayR
get a flat head screw driver or something to pry the metal clip off at the sides underneath where theres little indents in the metal, then once its off, just lift the little plastic flame adjuster up off the little white gear looking thing, and move it all the way to the side you would have it on if you wanted the flame low, but then move it all the way to the other side, and move it back to the low end and repeat untill the flame is how you want it.

just make sure you dont turn the thing too much.

Posted: Thu Mar 01, 2007 8:50 pm
by SmotPoker
Dr. Greenthumb wrote:It need to be a lighter with a butane control knob. You need to lift up the knob and keep turning the release(righty tighty, lefty loosy). The looser it is the higher the flame will be.

Don't use it for smoking. It's all fun and games till someone burns their eyebrows.
haha that happend to me...it was hilliarous!

Posted: Fri Mar 02, 2007 2:00 am
by SladeHino
It's called a Crack lighter lol. It's also a good way to get back at someone smoking , get the lighter to go like 5-6 inches and it burns there hair. :) Happened to me before sorta. But I got his ass back.

Posted: Fri Mar 02, 2007 2:23 am
by blazedsubaru
You can get the clear plastic ones with the black adjusting bit on the back, those lighters are good too, because when they start to die you can turn up the gas and they still work.

Posted: Fri Mar 02, 2007 3:28 am
by SpRi7e
I did that before when I was completely stoned and I burned my thumbs so bad from the flame coming back up that I have blisters all over my fingers.